Getting Familiar with Plumbing: Before Installing a Bathtub
Getting Familiar with Plumbing: Before Installing a Bathtub
Blog Article
Here in the next paragraph you can discover additional brilliant help and advice involving Tools You Need to Install a New Bathtub .
Mounting a bath tub isn't exactly brain surgery, yet it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably tough job. If the old bathtub is readily easily accessible, the task can relocate immediately; if you need to open up a wall surface to eliminate the old tub and also position the brand-new bath tub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will certainly need an assistant to leave the old tub and embeded in the brand-new one. Ensure you have qualified yourself for the job as well as are comfortable attempting it. As opposed to working with a contractor to take over a halfway-completed job, it is far better to think about utilizing one prior to you start. Chances are you might need a professional plumber to make tube connections.
This write-up will certainly assist you install a brand-new bath tub in your washroom if you have currently acquired a brand-new tub as well as don't require to change the setup of your previous water supply pipelines.
Your tools and also product checklist ought to comprise the following:
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your installment, then the first thing you should do is disconnect the water supply. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The procedure of removing the existing taps can be fairly bothersome because of the restricted accessibility that is usually the case.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will certainly originate from the pipes. When the supply pipes have been removed, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. Once the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old sealing compound.
Before moving on to fit the new taps, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic adapter to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end gives a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washers remain in area between the faucet as well as the sink. Safeguard the tap in place with the maker offered backnut. As soon as the faucet is firmly in place, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap connectors. The previous kind should be linked to the tap ends first, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Using both wooden boards under its feet, place the tub in the called for setting. The wooden boards are useful in equally spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four little points.
The following goal is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the tub up until the spirit level checks out level.
To mount faucets, fit all-time low of the outermost flexible faucet adapter to the proper supply pipe by making a compression join; then do the very same for the other faucet.
Turn on the water system and examine all joints and new pipework for leaks and tighten them if needed. Load the bath tub as well as additionally check the overflow outlet and the typical electrical outlet for leaks.
Finally, repair the bathroom paneling as defined in the producer's instruction manual. Tiling and securing around the bath tub needs to wait up until the tub has actually been utilized at the very least once as this will certainly resolve it right into its last position.
Planning for the Installment
To start with, the supporting framework provided with the bathroom ought to be fitted (if called for) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the tap features a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets device to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of both faucets utilizing 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final position.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to fracture an inflexible seal, creating the water to penetrate the wall between the bathroom and the tiling, bring about issues with dampness and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealants to blend in your components as well as installations. They are offered in tubes and also cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water prior to securing, to enable the activity experienced when the bathtub remains in usage. The sealant can break relatively early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently available on the market. It is recommended to fit the floor tiles utilizing waterproof or waterproof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
I am very focused on A Step-by-Step Guide to Installing a Bathtub and I'm hoping you liked the entire blog post. I beg you take the time to share this post if you appreciated it. Many thanks for going through it.
Top service? Contact. Report this page